12mm knurled switch actuators for 12mm AV switch holes. Available in red, gold, copper, and black. This is only for switch actuation or to be used as a plunger to press down onto your own tactile switch underneath, there is no switch built into these.
The smaller section is 11.9mm to easily fit into most common switch holes, and the knurled section is just under 14mm.
Switch plunger actuators designed for 12mm AV switch most commonly found on lightsaber hilts
Made from aluminum, these come in two finishes, standard machined finish and black anodized
Intended to assist with removable chassis electronic designs, these work best with any of the most recent removable chassis systems also here in other listings in the store. They can be used for any other lightsaber application where possible
Switch plunger mechanism is a 14mm OD at the widest part to accommodate the recessed area around most 12mm switch holes
Fully pressed in, these plungers have a low profile and are easy to press comfortably Depending on your specific hilt, some plungers may have a tighter fit than others
It is recommended to secure these with E6000 after final fitting to prevent them from coming out of your switch hole
Accent LED pixel for Neopixel lighting BTF Lighting WS2812C pixel Good for lightsaber crystal chamber builds, and other applications where accent lighting is required Labeled solder pads for data, positive, and ground wires to go in and out if wiring in series.
3D lightsaber saber vertical stand. Made from black PLA + material. Simple and sturdy, these stands will hold most sabers on the market no matter the shape of the pommel Depending on the size and weight of your saber, stand may have a slight bend with the saber resting against it
Stand dimensions are approximately 7” tall and 2” wide
Base cutout can hold a width up to 1 and 5/8” in outer diameter
OLED screen for saber builds using soundboards compatible with OLED screens. Available in white, blue, and yellow. Item comes with exterior pins presoldered for easy wiring, but can be easily cut and removed if you do not need them or space does not allow.
OLED total dimensions are 38mmx12mm. Protective screen layer can be peeled off.
Please refer to your soundboard manual for proper wiring installation.
Custom heatshrink wrap for 18650 batteries. Very easy to apply, wrap can slide directly over your battery and with the use of a heatgun, forms itself into place around the battery. Listing can be purchased as either just the heatshrink itself or one of our KeepPower 18650 3000mah 15A button top batteries with the heatshrink added on for you.
It is recommended to remove the outer layer of heatshrink around your battery if it has one already(KeepPower brand for example), to avoid any tolerances fitting issues with applying. The best tool for removing existing layer of wrap is a good X-Acto knife. Please do not overheat battery when using the heatgun to apply and shrink the wrap, it should not take more than 10-20 seconds to work properly.
3D printed grip guide for the 89Sabers MPP Vader hilt.
This item is printed in black PLA + filament. May be compatible with other models of the MPP hilt but not verified. 89Sabers hilt dimensions were used to make this guide.
Available for the 6 grip and 7 grip options, please make sure to select the correct desired one for your intended hilt configuration.
Easy to use, just removed the pommel, make sure the grip section is tightened all the way and slide the grip guide over the bottom. Align and secure each grip piece individually as necessary. When done with the grips just slide off the grip guide the same way it was put on.
3D printed adapter for USB Type C ports also sold here at Saberbay. Adapter is printed in black PLA + filament and not compatible with non USB-C ports. Made to fit in standard 12mm switch holes found on most saber hilts.
Can be purchased separately or with an included USB-C Port. In conjunction these parts can be used as an external access point for data transfer with your soundboard, or used together will a TC4056 charging module and male micro USB adapter(see wiring diagram for examples)
Adapter can snugly fit the USB-C port and is inserted from the top, with room below to solder wires onto afterwards. It is recommended to use a very small amount of glue to secure the port on the inside so it does not get pulled out with the cable after use.
3D printed grip guide for the 7Chambers Aniflex V2. Item is printed in black PLA + filament.
Grip guide will slide over the top of the grip section comfortable without scratching the surface. Simply line up the first grip with the guide and secure in place, then proceed to secure the remaining grips. Slide off the same way when finished. Grip guide spaces the grips evenly and centered in the grip section for no guesswork involved.
CIG invented the 1st Neopixel bezel combination momentary switch with a crystal clear 5mm led. A beautiful and functional switch for your lightsaber or industrial use.
Neopixel bezel switch can also be installed on other electrical panels. Eg Central fire alarm panels, Onboard vessels in the various control panel with an indicative light that is linked to the warning buzzer.
Neopixel Bezel comes in Standard chrome housing.
CIG Neopixel RGB Bezel with a momentary switch
- Neopixel combination with crystal clear 5mm LED (3-5 volt) - Built-in Momentary switch - PLA 3D printed parts - 5 x 20cm AWG32 wire pre-tinned for easy soldering - Free 330 ohm or 470 ohms 1/4 watt resistor for data control signal - 8mm Hex nut & washer included - Chrome Bezel housing - Drill hole 7.2 mm or 5/16" - Threading M8x0.75
3D printed grip guide for our Petro hilt. Easily slides over grip section of the hilt to help evenly space out the 4 grips that come with the hilt.
The guide will stop itself in the correct spot to also space out the grips to be centered on the grip section.
3D printed holder for a NPXL V3 shortpin connector. This listing is for the 3D printed holder only, NPXL connector is not included. Please only use a short pin connector for this piece. You can also use an ECO shortpin connector.
Intended for use in the Creepy Uncle, from Denis Lukyanov. Meant to go into the emitter cup of the hilt. You will need to sand the NPXL connector and the 3D printed holder for it to fit properly.
Dimensions are 20mmx5.25mm
Not intended for other hilts.
Micro USB to USB Port Adapter Cable for Data Transfer
Handy adapter cable for micro USB ports, commonly found on CFX and Proffie boards. These include a micro USB to USB port adapter, with a 30cm long ribbon cable. Easily plug this in to those hard to reach areas and tight spaces in your installs for USB board access. Will come assembled, however you can add some heatshrink to the connection points for added security and protection. This is not used for any sort of charging, this is a data transfer cable only.