Hilt Side Connectors

***Hilt side only***
Compatible with TCSS neo pixel connectors and Plecter pixel blades in function but will not fit in the holder of TCSS connectors
***Beskar Option is not available and is just their so the listing doesn't disappear from customers view when available options are sold out =D ***

Explanation here --> https://youtu.be/Fpv4AnaMPoY

***Hilt side only***
Compatible with TCSS neo pixel connectors and Plecter pixel blades in function but will not fit the pcb holders made for the TCSS pcb

Explanation here --> https://youtu.be/Fpv4AnaMPoY

These are already pre-soldered and pre-assembled with pins for your convenience. There is also 2 SMD resistors added for you.

The V3 NPXL manual can be found here. Tinyurl.com/npxlv3manual

Specifications and features:

-High quality components, manufacturing and assembly on factory
-Black PCB color with Gold Plated pads
-Compatible with TCSS/VV/PlecterPixel Blade side pcbs/blades
-Rated up to 18 Amperes max (up to 15 Amperes recommended) without current losses
-Reliable electrical connection due to high quality gold plated pogo pins made in US and Switzerland
-3-pole contact type: 1-pin Data, 4-pin Positive, 4-pin Negative
-High quality spring loaded pogo pins (short and long style) by Mill-Max and Preci-Dip
-16 on-board RGB (GRB color order) neopixel leds with separate Data input for Blade Plugs backlight
-On-board pixels have reverse polarity and short circuit protection, won’t be damaged
-Superior brightness and color, 50% brighter than the previous connector version
-Separate Blade Detection (BD) pin (5th Negative pin)
Dimensions:

Hilt pcb: 17.5x17.5x2.5mm (without pins)
Blade pcb: 17.5x17.5x1.6mm

Manual here:
https://tinyurl.com/npxlv3manual

*********As with all Neo Pixel products avoid excess moisture, Seal when possible and always store with blade plug inserted**********

***Hilt side only***
Compatible with TCSS neo pixel connectors and Plecter pixel blades in function but will not fit the pcb holders made for the TCSS pcb

Explanation here --> https://youtu.be/Fpv4AnaMPoY

These are already pre-soldered and pre-assembled with pins for your convenience. There is also 2 SMD resistors added for you.

The V3 NPXL manual can be found here. Tinyurl.com/npxlv3manual

Specifications and features:

-High quality components, manufacturing and assembly on factory
-Black PCB color with Gold Plated pads
-Compatible with TCSS/VV/PlecterPixel Blade side pcbs/blades
-Rated up to 18 Amperes max (up to 15 Amperes recommended) without current losses
-Reliable electrical connection due to high quality gold plated pogo pins made in US and Switzerland
-3-pole contact type: 1-pin Data, 4-pin Positive, 4-pin Negative
-High quality spring loaded pogo pins (short and long style) by Mill-Max and Preci-Dip
-16 on-board RGB (GRB color order) neopixel leds with separate Data input for Blade Plugs backlight
-On-board pixels have reverse polarity and short circuit protection, won’t be damaged
-Superior brightness and color, 50% brighter than the previous connector version
-Separate Blade Detection (BD) pin (5th Negative pin)
Dimensions:

Hilt pcb: 17.5x17.5x2.5mm (without pins)
Blade pcb: 17.5x17.5x1.6mm

1 each of:

NPXL V3 connector (pins assembled or non assembled)

NPXL 1” Uni Holder

NPXL Uni Holder Lens

Complete package for those who want to buy all correct parts at once

****** DOES NOT INCLUDE PCB OR LENS*****
******IF USING WITH LONG PIN YOU WILL NEED THE LENS TO SUPPORT THE PINS*******
****WORK WITH ECO AND STANDARD NPXL V3****
These new holders hold have a smaller foot print then other version 7mm Tall

They work for both long and short pin

You just purchase the separate lens for use with long pin

Will work with mag connect system with shortpin Npxl pcbs only.

Long pin and lens will not work with magconnect

NPXL V3 Connector with presoldered pins and presoldered wire leads.
Wire is high temp PTFE wire from Powerwerx, a top tier supplier of high quality wire.
Each wire is 12” long.
24AWG wire is used for positive and negative wires and 28AWG wire is used for the data line wire.
Red wire-positive leads
White wire-negative leads
Green wire-data line

Please refer to your soundboard manual for proper wiring and installation to your board.
All connectors are tested prior to being assembled.

Available in long and short pin options

****DOES NOT COME WITH THE BLACK PCB HOLDER OR THE SHTOKCUSTOMWORX PCB****
****DOES NOT WORK WITH SHORT PIN****
DOES NOT WORK FOR NPXL V2
****WILL NOT WORK WITH THE ECO NPXL VERSION****
****WILL NOT WORK WITH UNI PCB HOLDER****
***Good for adding to chassis designs***

This is the lens diffusion cover for the NPXL V3 LONGPIN PCB holders.
Work for Both in 1″ and 7/8″ OD version of the LONGPIN holders.
Does not work with short pins.
Machined from acrylic. It is not compatible with any third party PCB holder or the shortpin pcb holder.
Holder is press fit. Fits nicely

****DOES NOT COME WITH THE BLACK PCB HOLDER OR THE SHTOKCUSTOMWORX PCB****
****DOES NOT WORK WITH SHORT PIN******
****DOES NOT WORK FOR NPXL V2****
****WILL NOT WORK WITH THE ECO NPXL VERSION****

This is the lens diffusion cover for the UNI PCB holders.
Work for Both in 1″ and 7/8″ OD version of the LONGPIN holders.Does not work with short pins.
Machined from acrylic.

It is not compatible with any third party PCB holder or the shortpin pcb holder.
Holder is press fit. Fits nicely

NPXL V3 hilt side neopixel connector without the LED's.
These are the same exact size and basic function as the regular V3 connectors, with soldering pads for the neopixel positive and negative connections, as well as the data line and blade detection pads. 
These DO NOT have a spot for an SMD 0603 resistor, as most resistors will be built into the blade or on the soundboard now. 

Available as PCB only, short pin and long pin, assembled or non assembled versions.

The assembled versions will have the pins pre soldered, and the non assembled versions will include the selected pin type separately to solder yourself. The PCB only version will not include any pins.

CNC machined polycarbonate holder and lens holder for NPXL V3 longpin connectors. 
Not compatible for short pin connectors or non NPXL modules.

Two piece threaded design, no screws required.

Holder is 25.4mm or 1" in diameter and 8.75mm in height.

Proper installation requires light sanding of the connector so that it will fit into the base.

Align the pins with the proper holes and press up on the connector so that it pushes through, then screw on the bottom half. 

Press back down onto the pins and it should snap into place below. Use a small amount of glue if necessary to secure the holder.

Allows excellent shine through and diffusion for NPXL LED's.

*****PCB AND MAGNET SOLD SEPARATELY*****
WORKS W/ V2 NPXL shortpin, V3 NPXL shortpin and ECO
NPXL shortpin
This is designed to hold the ShortPin version of the NPXL 
This is the hilt side and for 1″ and 7/8" emitters. It is also designed for the short pins option only.
Machined from black ABS. It is not compatible with any third party PCB.
This holder is Mag Connect compatible. Magnets are sold separately here and graciously provided to us by The Saber Armory.
Please note, the magnets are a snug fit but hey will still need be glued in so the strong force of the magnets does not pull them out when they are near each other.
We recommend a low viscosity glue for this.
Be careful when doing this as the magnets are fragile.
Also, it is important to note that due to the tolerances, be sure to check the fitting of the holder inside the hilt before the magnets have been put it and after. Adding the magnets may expand the holder slightly making in a tighter fit. If this is the case lightly sanding the outside of the magnets using a sanding drum or sandpaper to reduce the outer diameter slightly is recommend. This will stop the holder from expanding after installing the magnets.
The PCB is press fit but it is recommended to hot glue the back end of the holder to secure. There are 2 small holes in case you want to drill and tap and use screws to secure the PCB.
The short pin version is not compatible with the clear lens cover.

*****PCB,LENSCOVER AND MAGNET SOLD SEPARATELY*****
WORKS W/ V2 NPXL LONGPIN V3 NPXL LongPin and ECO
NPXL LongPin
This is designed to hold the LongPin versions of the NPXL Lens Cover(will not work with lens cover made for the uni holder) and magconnect magnets .

This is the hilt side and for 1″ and 7/8" emitters.

Machined from black ABS. It is not compatible with any third party PCB.

This holder is Mag Connect compatible. Magnets are sold separately here and graciously provided to us by The Saber Armory.

Please note, the magnets are a snug fit but hey will still need be glued in so the strong force of the magnets does not pull them out when they are near each other.
We recommend a low viscosity glue for this.
Be careful when doing this as the magnets are fragile.

Also, it is important to note that due to the tolerances, be sure to check the fitting of the holder inside the hilt before the magnets have been put it and after. Adding the magnets may expand the holder slightly making in a tighter fit. If this is the case lightly sanding the outside of the magnets using a sanding drum or sandpaper to reduce the outer diameter slightly is recommend. This will stop the holder from expanding after installing the magnets.
The PCB is press fit but it is recommended to hot glue the back end of the holder to secure. There are 2 small holes in case you want to drill and tap and use screws to secure the PCB.

Here is the ShtokCustomWorx ECO NPXL V3 Hilt Side PCB Connector. 

This is the SHORT pin option.

• 1" PCB holder sold here.
• 7/8" PCB holder sold here. 

These are already pre-soldered and pre-assembled with pins for your convenience or you can choose an unassembled kit.

There is also 2 SMD resistors added for you. 

The V3 NPXL manual can be found here. 

Specifications and features:

• High quality components, manufacturing and assembling
• Reliable electrical connection
• 3-pole contact type: 1-pin Data, 3-pin Positive, 3-pin Negative
• Spring loaded Pogo pins (short and long style)
• 6 on-board 3535 SK6812 RGB Neopixel LEDs with separate Data input for Blade Plugs backlight
• Various connection options for Data input
• Fully compatible with TCSS and KR Sabers blade side PCB connectors.

Dimensions:

• Hilt pcb: 17.5x17.5x2.5mm (without pins)

1 each of:

NPXL V3 connector (pins assembled or non assembled)

NPXL 1” Long Pin Holder

NPXL V3 Long Pin Lens Cover

Complete package for those who want to buy all correct parts at once, with a slight discount versus buying all three individually 

Here is the ShtokCustomWorx ECO NPXL V3 Hilt Side PCB Connector.

This is the LONG pin option.

• 1" PCB holder sold here.
• 7/8" PCB holder sold here. 
• Lens cover sold here. 

These are already pre-soldered and pre-assembled with pins for your convenience or you can choose an unassembled kit.

There is also 2 SMD resistors added for you. 

Specifications and features:

• High quality components, manufacturing and assembling
• Reliable electrical connection
• 3-pole contact type: 1-pin Data, 3-pin Positive, 3-pin Negative
• Spring loaded Pogo pins (short and long style)
• 6 on-board 3535 SK6812 RGB Neopixel LEDs with separate Data input for Blade Plugs backlight
• Various connection options for Data input
• Fully compatible with TCSS and KR Sabers blade side PCB connectors.

Dimensions:

• Hilt pcb: 17.5x17.5x2.5mm (without pins)