Hilts

The “Creepy Uncle”, Luke Skywalker’s hilt from The Last Jedi.

Designed and manufactured by Denis Lukyanov.

This is an empty DIY kit, and does not include installation or cosmetic work.

Each kit contains the following:

-Empty hilt, mostly assembled except for clamp card and control box arrows 

-Acrylic/metal blade plug (1” sized, emitter takes 1” blades)

-metal Tri-ring for pommel attachment 

-double sided clamp card for different variations 

-3D printed parts for low profile emitter PCB holder for Neopixel builds, as well as control box helper board holder 

-PCB helper board for control box wiring, includes labeled soldering pads for tactile switches and accent leds

-two tactile switches 

-red and green 3mm accent leds

-red and green arrows for control, glue in place from outside the control box 

-aluminum heatsink adapter for tricree LED builds

-Allen wrench for blade retention 

Hilt can come apart at the pommel, and fit a 28mm speaker, as well as above the control box area of the hilt below the grenade grip.

Hilt is made from high quality aluminum and brass parts for the thin neck area.

 

Designed and produced by Saberbay, this is Petro’s hilt based off the character from the Clone Wars series.
Available as an empty hilt, with or without an install parts package, which will include all parts and chassis necessary to do your own install.
We are not offering install services at this time.
Install packages with soundboards included are limited at this time.
If soundboard included install packages are not available, we have install packages without soundboards available in another listing. You will need to source your own soundboard.

Hilt kit is broken down into multiple parts and will arrive mostly assembled for you. See listing pictures for example of all parts.
Hilt takes a 1” blade in the emitter
Grips can be added on with or without a grip guide(sold separately).
Grip pieces and clamp cards will come with strong double sided adhesive to apply to hilt control box and grip section.

Buyer is responsible for their own install and proper handling and use of parts. We are not liable for third party damage of parts installation.
Parts kits are sold as is, and can not be substituted with other parts not listed.

This couplers is meant only for the Vestige we offer here in the shop

It is adjustable so you can line up the two hilts to your desire.

Adjustment is made by loosening the screws and adjusting then re-tightening the screws

Please note in the photos you can see a reflection of the LED lights

There are no marks on these . They are high polished like the hilts

Introducing the first SithLord Sabers production run hilt, The Menace.

The Menace combines design elements of The Old Republic with original concepts to create a one of a kind hilt to add to your collection.
Featuring fierce serrated blades, and a unique pyramid-esque layouts of switch plungers, this hilt has a pleasantly surprising ergonomic feel for either single or two handed use.
With detachable blades and a blank slate that begs for customization, you can truly make The Menace one to call your own. With add on features such as various soundboard options for installation, powdercoating, weathering, leather wraps, and etching, the possibilities are endless. Each Menace also includes a free custom blade plug with your order.

Install options include CFX and GoldenHarvestV3
Currently only offered in neopixel setups
Additional add ons include leather wraps, powdercoating, weathering, and third party etching. 
Hilts are installed with a removable chassis and a two button function for each board installation.
All installs have a removable battery option as well as a killswitch feature for cycling power.
For neopixel connections, we use ShtokCustomWorx PCB's for emitter illumination even without a blade inserted. All hilts take a 1" blade
We have a large selection of various powdercoating colors and options, and can work with you to determine the look you want for your hilt. For specific customization requests, please send the shop a message regarding your order.

THIS IS A SEND IN SERVICE
You must provide the hilt to be installed with the specs outlined below. Customer is responsible for their own shipping costs to send in the hilt. Please make sure the hilt is securely packaged and safe to travel. We are not liable for any damage occurred to the hilt in transit to us.
The hilt must be the 89Sabers Graflex hilt version only. Any saber sent in that is not the correct version will need to be sent back and buyer is responsible for return shipping.

Send in service price includes full install and return shipping for US customers. Send in services can not use any customer provided chassis or parts.

After purchase please send your hilt to this address and make sure to include your name, and order number in the box with your hilt:

Saberbay

3528 Crescent Meadow Dr.

Bakersfield, CA 93308

Fully installed 89Sabers Graflex hilt setup in A New Hope configuration. Takes a 1" blade(not included, our 1" blades are recommended for this hilt as the emitter has a tighter tolerance than most)

Installed with the following components:
-Crystal Focus X soundboard loaded with over 25 sound fonts. Board is installed SD card side up for easy access.

-NPXL V3 Connector with 1" holder and Lens cover

-Saberbay 89Sabers Graflex chassis

-Two button setup, red button for main, slide switch for auxiliary

-removable 18650 KeepPower 3000mah 15A battery

-28mm 8ohm/2W bass speaker

-High amp killswitch

Also includes our 1" Graflex blade plug, 89Sabers collectors box and extra accessories that come with the empty saber kit(extra clamp cards, grips, D ring attachments)

All installed sabers come with a 30 day warranty for normal use. Any user misuse of electrical components outside of their normal use or tampering with wiring is not covered under warranty. Please ask any questions about this product before purchasing.

THIS IS A SEND IN SERVICE
You must provide the hilt to be installed with the specs outlined below. Customer is responsible for their own shipping costs to send in the hilt. Please make sure the hilt is securely packaged and safe to travel. We are not liable for any damage occurred to the hilt in transit to us.
The hilt must be the 89Sabers Obi Wan TPM hilt version only. Any saber sent in that is not the correct version will need to be sent back and buyer is responsible for return shipping.

Send in service price includes full install and return shipping for US customers. Send in services can not use any customer provided chassis or parts.

After purchase please send your hilt to this address and make sure to include your name, and order number in the box with your hilt:

Saberbay

3528 Crescent Meadow Dr.

Bakersfield, CA 93308

Installed 89Sabers Obi Wan TPM hilt.
This has been installed with the following electronics.

-Saberbay Obi TPM Chassis kit

-Crystal Focus X soundboard from Plecter Labs(preloaded with over 25 sound fonts)

-NPXL V3 connector and lens cover

-Two button setup(Red for main and Brass for auxiliary)

-Blue OLED screen built into chassis

-Removable 18650 KeepPower 3000mah 15A battery

-KR Sabers 22mm speaker

This hilt takes a 1" blade(not included, we recommend our 1" blades for this hilt as the emitter is a tighter fit)
Sale includes the fully installed hilt, blade plug, collectors box from 89Sabers, and extra accesories included with the original kit(extra pommel cubes)

Please refer to the soundboard manual for full list of features and functions and how to use the board.

All installed sabers are covered by a 30 day warranty. Any user error or misuse or tampering with the electronics outside of their intended use is not covered. Please ask any questions you may have before purchasing.

THIS IS A SEND IN SERVICE
You must provide the hilt to be installed with the specs outlined below. Customer is responsible for their own shipping costs to send in the hilt. Please make sure the hilt is securely packaged and safe to travel. We are not liable for any damage occurred to the hilt in transit to us.
The hilt must be the 89Sabers K4V2 hilt version only. Any saber sent in that is not the correct version will need to be sent back and buyer is responsible for return shipping.

Send in service price includes full install and return shipping for US customers. Send in services can not use any customer provided chassis or parts.

After purchase please send your hilt to this address and make sure to include your name, and order number in the box with your hilt:

Saberbay

3528 Crescent Meadow Dr.

Bakersfield, CA 93308

Fully installed 89Sabers Kenobi K4V2 hilt setup in A New Hope configuration. Takes a 1" blade(not included, our 1" blades are recommended for this hilt as the emitter has a tighter tolerance than most)

Installed with the following components:
-Crystal Focus X soundboard loaded with over 17 sound fonts. Board is installed SD card side up for easy access.

-Saberbay 89Sabers K4V2 removable chassis

-NPXL V3 short pin connector

-Two button setup

-removable 18650 KeepPower 3000mah 15A battery

-28mm Saberbay X-BASS 4ohm/3W bass speaker

-High amp killswitch

-OLED Screen

All installed sabers come with a 30 day warranty for normal use. Any user misuse of electrical components outside of their normal use or tampering with wiring is not covered under warranty. Please ask any questions about this product before purchasing.

'The Little One', a Clone Wars inspired Yoda hilt designed and produced between 5280 Concepts and Dagobah Swamp. 
This empty hilt kit comes with the fully assembled saber, working dual button switch plungers in the control box, two shine greeblies to utilize some accent LED's underneath, as well as an extra pommel and emitter ring.
Allows for a 7/8" blade(not included). 
A custom chassis is already designed for this saber, available on Shapeways for an ECO option and also a metal crystal chamber Master Chassis. 

Link to the Shapeways store below:

https://www.shapeways.com/shops/5280-printing?li=pb

The Master Sentinel hilt, a collaboration between Wade Sabers LLC, SithLord Sabers, and A&A Designs. 

This is an empty DIY saber, full of unlimited customization options. 
Please watch the Youtube video link below for proper assembly/disassembly if required.

https://www.youtube.com/watch?v=yxOb1njyf38&t=62s

Hilt design features a polished surface(some hilts may have some micro scratches, can easily be buffed out if desired), two independent working switch plungers, 1" emitter size for blades, multiple shrouds, custom grip sleeve which can also be removed in place for other things like leather or custom wraps, custom machined D-ring attachment using shoulder bolts, and bottom access through the pommel. 

Inner hilt dimensions features 1.1" of install space for all major soundboard components and up to a 28mm bass speaker for electronics installs.

All hilt purchases include the assembled hilt, collectors box, plaque, blade retention allen wrench, and set of shroud inserts which can be adhered to the hilt through your own adhesive methods.

For custom cosmetic work, please message the store for rates on powdercoating and other custom work. We do not provide etching services.

The exclusive Kyle Katarn V3 hilt from WarSabers. This is an empty DIY saber kit so you will need to do your own install for this hilt. Please see the hilt specs below for hilt dimensions. The red buttons serve as switch plungers for a tactile switch to be wired up underneath.
Link for custom chassis design from WarSabers on their Shapeways store.

https://www.shapeways.com/shops/warsabers?section=Kyle%20Katarn%20V3%20(2021)%20(Warsabers)&s=0&fbclid=IwAR20yMCE_Ff9VZhC2SeH9Oqa5NbkCXwXVflp14mDcdm01FXOgaI_sJk_T9s

Assembly instructional video link below:

https://www.youtube.com/watch?v=wCNQNYkwDL8&t=424s

 

Hilt size:

• Length – 320 mm.

Dimensions for chassis space:

• Length – 220 mm;
• ID – 22 mm.

Dimensions for aditional speaker space:

• Length – 16 mm;
• ID – 30 mm.

Dimensions for blade:

• ID – 25,4 mm (1″)

Check out custom templates for various Master Sentinel finishes. You can use these as examples to order identical ones of your own or to use as identifying layouts for other customs.

Prices for the template options are pre-set configurations based on the colors and layout options shown in the examples.

These are made to order, and can also be purchased with an installed chassis or DIY chassis kit.

Our newest entry line DIY hilt, the Valor!
Made from CNC machined 6061 aluminum, this hilt features a polished finish and is ready for your customization. 
Main design features of this hilt include a removable one piece shroud, single 12mm switch hole support, (which can support a variety of our 12mm sized products), diamond knurling on top and bottom of the grip section, a hidden sound venting system, and ample internal space for 1" blades and up to 28mm speakers.

Shroud design allows for hidden blade retention methods, utilizing one of the shroud screws as a blade retention. Each hilt will include the correct number of flat head allen screws to sit flush with the shroud. 
The emitter also features shine through holes around the entire upper section.
The hilt separates into several pieces, with a detachable grip and pommel section to allow easy chassis installation options. Chassis retention can be used by the optional M2 threaded hole at the bottom of the emitter piece above the threads. 
The pommel has hidden sound venting which is concealed by the pommel insert.

This will include the empty saber only, no other parts or electronics are included.

Total weight of the empty hilt is 5 ounces, with a total length of 10 5/8" from top of the shroud to the bottom of the pommel.

THIS IS A PREORDER, the saber run has not been completed and expected ETA is end of June or July. This timeframe does not guarantee the saber will be ready by that time.
Please read all info and pricing options as you will be expected to pay the full amount for the option chosen before receiving your saber.

The preorder price for the saber is $465. This includes the empty hilt in polished aluminum, fully assembled, a free chassis included of your desired soundboard, collectors box, and blade retention wrench.
Add ons include: 
-basic powdercoating shown in pictures $75
-Elite Package powdercoating shown in pictures $200
-Elite Package pre-installed versions $450 for CFX and Proffie, $400 for GHV3

Hilt design features will include acceptance for a 1" blade, and two switch actuators for up to two switch function for installs.
Main body is a two machined halves, welded and machine finished to be a single piece. Pommel is a single piece with sound venting. Accent ring and emitter shroud slide over the main body and are held in place by set screws. Emitter accent piece goes over the emitter shroud and holds itself and the emitter shroud in place with a set screw. Control box holds the two switch actuators which can press down onto tactile switches built into the removable chassis. Contol box is held in place by two set screws, with a cutout opening in the main body underneath.
Chassis design is a fully removable chassis, using NPXL shortpin connectors, removable 18650 battery, two switch setup, high amp killswitch and 22mm Veco bass speaker. All chassis will include a unique chassis removal tool, the chassis is inserted and removed from the emitter.

This is our newest saber kit offering featuring Obi Wan Kenobi's saber from ROTS. This hilt also includes an extra swappable emitter, to swap between the ROTS version and the newest version shown in the new Obi Wan Kenobi series. 
This listing does not include any electronics or other parts not shown in the pictures. This listing includes the saber hilt, extra emitter screws for blade retention, allen wrench, and custom box for storage. 
The emitter takes a 1" blade, and the hilt is meant to utilize the clamp card for switch activation. Please see the pictures for a breakdown of how the hilt is disassembled. 
You can also purchase the weathered version of this saber shown in the picture examples, these are limited while supplies last for this version.

This is our newest DIY hilt offering featuring Anakin Skywalker's saber hilt from ROTS. This listing is for the lightsaber hilt only, and does not include any other electronics or other parts not shown. 
This saber will need to use a 7/8" size blade, and is meant to utilize the clamp card for switch activation. You can see the pictures for a breakdown of the disassembled hilt. The clamp card may have a plastic cover for protection that you can remove by hand.
This listing will include the saber, extra blade retention screw and wrench, and custom box for storage.